1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Turn out fixing screws and remove back section of the central console.

On the models equipped with system of additional safety try not to subject to shock loadings the diagnostic SRS block!

3. Remove a pillow of a back seat.
4. Remove a collar of fastening of the central section of a driving cable and release the plug through passage.
5. The car also establish to Poddomkratta it on props.
6. Remove back wheels, brake drums and shoe assemblies (see the Sections Removal, installation and check of a condition of the brake drum and Check of a condition of brake boots).
7. Disconnect a tip of a driving cable from the lever of the parking brake.
8. Squeeze clamps and disconnect a driving cable from a board of the brake mechanism.
9. Release a cable from all provided intermediate clamps and remove it from the car.

1. Sometimes driving cables for identification are marked by drawing multi-colored tags. Check cables for existence of identification marking.
2. Connect a cable to the back actuation mechanism and fix it by a special collar and a spring clamp.
3. Establish brake boots and a drum.
4. Freely fix a cable in intermediate clamps.
5. Connect cables to the actuation mechanism in interior of the car.
6. Execute adjustment of boots of brake mechanisms of back wheels.
7. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
8. Having finished all adjustments, several times cock and release the parking brake.
9. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
10. Install the central console and assembly of a back seat.
11. Connect a negative wire to the battery.
12. Check reliability of keeping of the car the parking brake on a bias.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Turn out fixing screws and remove back section of the central console.

On the models equipped with system of additional safety try not to subject to shock loadings the diagnostic SRS block!

3. Remove a pillow of a back seat.
4. Release an adjusting nut and disconnect driving cables from the actuation mechanism.
5. Remove a collar of fastening of the central section of a driving cable and release the plug through passage.
6. The car also establish to Poddomkratta it on props.
7. Disconnect a tip of a driving cable from assembly of the parking brake.
8. Squeeze clamps and disconnect a driving cable from a board of the brake mechanism.
9. Release a cable from all provided intermediate clamps and remove it from the car.

1. Sometimes driving cables for identification are marked by drawing multi-colored tags. Check cables for existence of identification marking.
2. Connect a cable to the back actuation mechanism and fix it by a special collar and a spring clamp.
3. Freely fix a cable in intermediate clamps.
4. Connect cables to the actuation mechanism in interior of the car.
5. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
6. Tightening an adjusting nut, choose a cable weak point.
7. Execute adjustment of the parking brake (see the Section Adjustment of the Parking Brake).
8. Having finished adjustment, several times cock and release the parking brake.
9. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
10. Install the central console and assembly of a back seat.
11. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove side panels of finishing of the central console.
3. On models with RKPP remove the handle from the gear shifting lever. On models remove facing of the lever of the selector from AT.
4. Dismantle the panel of switches / a console ware box and turn out two fixing screws located under her / him.
5. Remove the panel of facing of the radio receiver.
6. Remove the radio tape recorder.
7. Remove the internal panel of finishing of the console in turn out two screws located under it.
8. Turn out the remained fixing screws located on each side console assembly.
9. Remove the central console.
10. Wring out a first line of a pillow of a back seat down, release the blocking levers and remove a pillow.
11. Weaken the cable tension regulator on assembly of the equalizer.
12. Remove a collar of fastening of the central section of a driving cable and release the plug through passage.
13. The car also establish to Poddomkratta it on props.
14. Remove back wheels, brake drums and shoe assemblies (see the Sections Removal, installation and check of a condition of the brake drum and Check of a condition of brake boots).
15. Disconnect a tip of a driving cable from the lever of the parking brake.
16. Squeeze clamps and disconnect a driving cable from a board of the brake mechanism.
17. Release a cable from all provided intermediate clamps and remove it from the car.

1. Sometimes driving cables for identification are marked by drawing multi-colored tags. Check cables for existence of identification marking.
2. Connect a cable to the back actuation mechanism and fix it by a special collar and a spring clamp.
3. Establish brake boots and a drum.
4. Freely fix a cable in intermediate clamps.
5. Connect cables to the actuation mechanism in interior of the car. As rotation of an adjusting nut choose a weak point of hummock assembly.
6. Execute adjustment of the parking brake (see the Section Adjustment of the Parking Brake).
7. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
8. Having finished all adjustments, several times cock and release the parking brake.
9. Execute adjustment of boots of brake mechanisms of back wheels.
10. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
11. Install the central console and assembly of a back seat.
12. Connect a negative wire to the battery.
13. Check serviceability of functioning of electric equipment which is built in in console assembly.
14. Check reliability of keeping of the car the parking brake on a bias.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove side panels of finishing of the central console.
3. On models with RKPP remove the handle from the gear shifting lever. On models remove facing of the lever of the selector from AT.
4. Dismantle the panel of switches / a console ware box and turn out two fixing screws located under her / him.
5. Remove the panel of facing of the radio receiver.
6. Remove the radio tape recorder.
7. Remove the internal panel of finishing of the console in turn out two screws located under it.
8. Turn out the remained fixing screws located on each side console assembly.
9. Remove the central console.
10. Wring out a first line of a pillow of a back seat down, release the blocking levers and remove a pillow.
11. Weaken an adjusting nut and disconnect back sections of hummock assembly from the actuation mechanism.
12. Remove a collar of fastening of the central section of a driving cable and release the plug through passage.
13. The car also establish to Poddomkratta it on props.
14. Release a clamp and a lock ring of fastening of a cable to a support of the brake mechanism of a back wheel.
15. Disconnect a cable tip from a support.
16. Release a cable from all provided intermediate clamps and remove it from the car.

1. Sometimes driving cables for identification are marked by drawing multi-colored tags. Check cables for existence of identification marking.
2. Connect a cable to the actuation mechanism on assembly of a support and fix it by means of a clamp and a lock ring.
3. Freely fix a cable in intermediate clamps.
4. Connect cables to the actuation mechanism in interior of the car. Having tightened an adjusting nut, choose a weak point of hummock assembly.
5. Adjust the course of a driving cable (see the Section Adjustment of the Parking Brake).
6. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
7. Having finished all adjustments, several times cock and release the parking brake.
8. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
9. Install the central console and assembly of a back seat.
10. Connect a negative wire to the battery.
11. Check serviceability of functioning of electric equipment which is built in in console assembly.
12. Carry out trial runs of the car.
13. Check reliability of keeping of the car the parking brake on a bias.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. On models with RKPP remove the handle from the gear shifting lever. On models remove facing of the lever of the selector from AT.
3. Dismantle instrument section of the central console.
4. Remove a console ware box.
5. Turn out two screws of fastening of the central section of the console.
6. Turn out four the screw of fastening of side panels and remove the console from the car.
7. Weaken an adjusting nut and release a driving cable from interior of the car.
8. The car also establish to Poddomkratta it on props.
9. Remove back wheels, brake drums and shoe assemblies (see the Sections Removal, installation and check of a condition of the brake drum and Check of a condition of brake boots).
10. Disconnect a tip of a driving cable from the lever of the parking brake.
11. Squeeze clamps and disconnect a driving cable from a board of the brake mechanism.
12. Release a cable from all provided intermediate clamps and remove it from the car.

1. Connect a cable to the back actuation mechanism and fix it by a special collar and a spring clamp.
2. Establish brake boots and a drum.
3. Freely fix a cable in intermediate clamps.
4. Connect cables to the actuation mechanism in interior of the car.
5. As rotation of an adjusting nut choose a weak point of hummock assembly.
6. Execute adjustment of the parking brake (see the Section Adjustment of the Parking Brake).
7. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
8. Having finished all adjustments, several times cock and release the parking brake.
9. Execute adjustment of boots of brake mechanisms of back wheels.
10. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
11. Install the central console.
12. Connect a negative wire to the battery.
13. Check serviceability of functioning of electric equipment which is built in in console assembly.
14. Check reliability of keeping of the car the parking brake on a bias.

1. Unlike the options considered earlier on these models the parking brake is not built in a support of the brake mechanism. In this case the separate frictional boots established behind a brake disk are used.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. On models with RKPP remove the handle from the gear shifting lever. On models remove facing of the lever of the selector from AT.
4. Remove instrument section of the central console.
5. Remove a console ware box.
6. Turn out two screws of fastening of the central section of the console.
7. Turn out four side screws and remove console assembly.
8. Release an adjusting nut and release hummock assembly from interior of the car.
9. The car also establish to Poddomkratta it on props.
10. Remove a back wheel, a brake support and a disk (see the Sections Removal and installation of supports of disk brake mechanisms and Removal, check of a state and installation of a brake disk).
11. Take off frictional boots of the parking brake (see the Section Removal and installation of frictional boots of the parking brake (model with disk brake mechanisms of back wheels)).
12. Disconnect hummock assembly from the executive lever of the parking brake.
13. Release clamps and release a cable from a brake board.
14. Release a clamp and a lock ring of fastening of a cable to a support of the brake mechanism of a back wheel.
15. Release a cable from all provided intermediate clamps and remove it from the car.

1. Connect a cable to the back actuation mechanism and fix it by means of a clamp and a lock ring.
2. Establish frictional boots of the parking brake.
3. Establish a brake disk and a support (see the Sections Removal and installation of supports of disk brake mechanisms and Removal, check of a state and installation of a brake disk).
4. Freely fix a cable in intermediate clamps.
5. Connect cables to the actuation mechanism in interior of the car.
6. Having tightened an adjusting nut, choose a weak point of hummock assembly.
7. Adjust the course of a driving cable (see the Section Adjustment of the Parking Brake).
8. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
9. Having finished all adjustments, several times cock and release the parking brake.
10. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
11. Install the central console.
12. Connect a negative wire to the battery.
13. Check serviceability of functioning of electric equipment which is built in in console assembly.
14. Carry out trial runs of the car.
15. Check reliability of keeping of the car the parking brake on a bias.

1. On the Diamante models back wheels are equipped with disk brake mechanisms with separate frictional boots of the parking brake. Boots are located behind a brake disk.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. On models with RKPP remove the handle from the gear shifting lever. On models remove facing of the lever of the selector from AT.
4. Remove the ashtray/panel of switches from assembly of the central console.
5. Turn out two consoles of the screw located in the central part.
6. Turn out side screws and remove console assembly from the car.

On the models equipped with system of additional safety try not to subject to shock loadings the diagnostic SRS block!

7. Release an adjusting nut and, having pulled down, release hummock assembly from interior of the car.
8. The car also establish to Poddomkratta it on props.
9. Remove a back wheel, a brake support and a disk (see the Sections Removal and installation of supports of disk brake mechanisms and Removal, check of a state and installation of a brake disk).
10. Take off frictional boots of the parking brake (see the Section Removal and installation of frictional boots of the parking brake (model with disk brake mechanisms of back wheels)).
11. Disconnect hummock assembly from the executive lever of the parking brake.
12. Release clamps and release a cable from a brake board.
13. Release a cable from all provided intermediate clamps and remove it from the car.

1. Connect a cable to the back actuation mechanism and fix it by means of a clamp and a lock ring.
2. Establish frictional boots of the parking brake.
3. Establish a brake disk and a support (see the Sections Removal and installation of supports of disk brake mechanisms and Removal, check of a state and installation of a brake disk).
4. Freely fix a cable in intermediate clamps.
5. Connect cables to the actuation mechanism in interior of the car.
6. Having tightened an adjusting nut, choose a weak point of hummock assembly.
7. Adjust the course of a driving cable (see the Section Adjustment of the Parking Brake).
8. Check reliability of a zashchelkivaniye of hummock assembly in all provided clamps.
9. Having finished all adjustments, several times cock and release the parking brake.
10. Poddomkratte a car back also check freedom of rotation of back wheels at the released parking brake.
11. Install the central console.
12. Connect a negative wire to the battery.
13. Check serviceability of functioning of electric equipment which is built in in console assembly.
14. Check reliability of keeping of the car the parking brake on a bias.