3726b8fd

11:23. Removal and installation of frictional boots of the parking brake (model with disk brake mechanisms of back wheels)

Components of the drive of the parking brake on the Galant models since 1994 of the issue with disk brake mechanisms of back wheels

1 — the Support of the brake mechanism
2 — the Brake disk
3 — the Anchor spring of a back boot
4 — the Anchor spring of a forward boot
5 — Pruzhina of an adjusting castor
6 — the Regulator
7 — the Expansion level

8 — the Returnable spring of an expansion level
9 — the Plate of the directing spring
10 — the Directing boot spring
11 — the Anchor finger
12 — Frictional boots
13 — the Clamp
14 — the Trosovy drive of the parking brake


Components of the drive of the parking brake on the Diamante 1992 ÷ models of 1996 of the issue.

1 — the Wheel sensor (models with ABS)
2 — the Support of the brake mechanism
3 — the Brake disk
4 — Pruzhina of an adjusting castor
5 — the Plate of the directing spring
6 — the Directing boot spring
7 — the Anchor finger
8 — the Regulator
9 — the Anchor spring of a back boot
10 — the Anchor spring of a forward boot

11 — the Expansion level
12 — the Returnable spring of an expansion level
13 — Frictional boots
14 — the Clamp
15 — the Protective cover of a stupichny nut
16 — Stupichnaya a nut
17 — the Washer
18 — the Wheel bearing
19 — the Brake board


Components of the parking brake on the Diamante models since 1997 of the issue.

1 — the Bolt of fastening of a support
2 — the Support
3 — the Brake disk
4 — the Wheel sensor
5 — Bolts of fastening of stupichny assembly
6 — Stupichnaya assembly
7 — the Screw of the directing spring of a frictional boot
8 — the Directing boot spring

9 — the Frictional boot
10 — the Antispray screen
11 — the Tip of fastening of a driving cable to the executive lever
12 — the Brake board
13 — the Adjusting castor
14 — the Cam
15 — the Pusher
16 — the Executive lever


The Galant models since 1994 of the issue and Diamante 1992 ÷ of 1996 of the issue.

Removal

 PERFORMANCE ORDER

1. Components of the drive of the parking brake on the corresponding models are presented on illustrations.
2. The car also establish to Poddomkratta it on props.
3. Remove assembly of a brake support (see the Section Removal and installation of supports of disk brake mechanisms).
4. Remove a brake disk (see the Section Removal, check of a state and installation of a brake disk).

5. Remove anchor springs of forward and back frictional boots.

6. Remove a spring of an adjusting castor and assembly of the regulator.
7. Remove an expansion level with a returnable spring.
8. Remove the directing springs and anchor fingers of frictional boots.
9. Remove shoe assemblies.
10. Release clamps, turn out fixing bolts and remove a cable of the drive of the parking brake.


Installation

 PERFORMANCE ORDER

Installation is made upside-down. Track correctness of installation of anchor springs, - they have various power characteristics and one of them is marked with paint.


The Diamante models since 1997 of the issue.

Removal

 PERFORMANCE ORDER

1. The design of the parking brake on the Diamante models since 1997 is presented to the issue on an illustration.
2. The car also establish to Poddomkratta it on props.
3. Remove a support (see the Section Removal and installation of supports of disk brake mechanisms).
4. Remove a brake disk (see the Section Removal, check of a state and installation of a brake disk).
5. Turn out screws of the directing springs and remove shoe assemblies from a brake board.


Installation

 PERFORMANCE ORDER

Installation is made upside-down.