1. Details of installation of RPM meters of forward wheels on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! In order to avoid operation of safety cushions start dismantle of the sensor not less than 90 seconds later after shutdown of the battery.

3. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
4. Remove a loker of protection of a wheel arch.
5. Disconnect an electrical wiring from the wheel sensor.
6. Remove clamps of fastening of a plait of an electrical wiring of the sensor.
7. Remove the sensor from a basic arm.

1. Install the sensor on a basic arm and tighten a fixing bolt.
2. Establish clamps of fastening of a plait of an electrical wiring.
3. Connect an electrical wiring to the sensor.
4. Connect a negative wire to the battery.

1. Details of installation of RPM meters of back wheels on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! In order to avoid operation of safety cushions start dismantle of the sensor not less than 90 seconds later after shutdown of the battery.

3. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
4. Disconnect an electrical wiring from the wheel sensor.
5. Remove clamps of fastening of a plait of an electrical wiring of the sensor.
6. Turn out a fixing bolt and remove the wheel sensor.

1. Install the sensor on the regular place and freely tighten a fixing bolt.
2. Establish clamps of fastening of a plait of an electrical wiring.
3. Connect an electrical wiring to the sensor.

4. By means of not magnetic probe of lezviyny type adjust a gap between the sensor and its rotor, - the required value makes 0.3 — 0.9 mm.

5. Finally tighten fixture and double-check correctness of installation of a gap. In case of need repeat adjustment.
6. Connect a negative wire to the battery.

1. Details of installation of wheel sensors on the Galant models are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! In order to avoid operation of safety cushions start dismantle of the sensor not less than 90 seconds later after shutdown of the battery.

3. The car also establish to Poddomkratta it on props. Remove the corresponding forward wheel.
4. Remove a loker of protection of a wheel arch.
5. Disconnect an electrical wiring from the wheel sensor.
6. Turn out coupling bolts and remove collars of fastening of a plait of an electrical wiring of the sensor.
7. Turn out a fixing bolt and remove the wheel sensor.

1. Install the sensor on the regular place and tighten a fixing bolt.

The gap between the sensor and its rotor is not subject to adjustment, however has to be checked. The required value makes 28.2 ÷ 28.4 mm. At an exit of result of change out of limits of admissible range replace the sensor or a rotor.

2. Fix a sensor electrical wiring plait by bandage collars, - strongly tighten coupling bolts.
3. Connect an electrical wiring to the sensor.
4. Establish a loker of protection of a wheel arch.
5. Establish into place a wheel and lower the car on the earth.
6. Connect a negative wire to the battery.

1. Details of installation of wheel sensors are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! In order to avoid operation of safety cushions start dismantle of the sensor not less than 90 seconds later after shutdown of the battery.

3. The car also establish to Poddomkratta it on props. Remove the corresponding forward wheel.
4. Disconnect an electrical wiring from the wheel sensor.
5. Turn out coupling bolts and remove collars of fastening of a plait of an electrical wiring of the sensor.
6. Turn out a fixing bolt and remove the wheel sensor.

1. Install the sensor on the regular place and tighten a fixing bolt.

The gap between the sensor and its rotor is not subject to adjustment, however has to be checked. The required value makes 28.2 ÷ 28.4 mm. At an exit of result of change out of limits of admissible range replace the sensor or a rotor.

2. Fix a sensor electrical wiring plait by bandage collars, - strongly tighten coupling bolts.
3. Connect an electrical wiring to the sensor.
4. Establish into place a wheel and lower the car on the earth.
5. Connect a negative wire to the battery.

1. Details of installation of RPM meters of forward wheels on the Diamante models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! In order to avoid operation of safety cushions start dismantle of the sensor not less than 90 seconds later after shutdown of the battery.

3. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
4. Remove a loker of protection of a wheel arch.
5. Disconnect an electrical wiring from the wheel sensor.
6. Remove clamps of fastening of a plait of an electrical wiring of the sensor.
7. Remove the wheel sensor.

1. Install the sensor on the regular place and tighten it with the required effort (12 H • м).
2. Establish clamps of fastening of a plait of an electrical wiring.
3. Connect an electrical wiring to the sensor.
4. Connect a negative wire to the battery.

1. Details of installation of RPM meters of back wheels on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! In order to avoid operation of safety cushions start dismantle of the sensor not less than 90 seconds later after shutdown of the battery.

3. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
4. Disconnect an electrical wiring from the wheel sensor.
5. Remove clamps of fastening of a plait of an electrical wiring of the sensor.
6. On all-wheel drive (AWD) models remove a hummock bandage.
7. Turn out a fixing bolt and remove the wheel sensor together with a sealing ring.

1. Install the sensor on the regular place (do not forget to replace a sealing ring) and tighten it with the required effort (12 H • м).
2. Establish clamps of fastening of a plait of an electrical wiring.
3. Establish a hummock bandage.
4. Connect an electrical wiring to the sensor.
5. Connect a negative wire to the battery.