1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props. Remove both back wheels.
3. Prop up the lower lever of a suspension bracket a jack.
4. Mark the adjusting provision of the top plate of a screw spring.
5. On models with an active suspension bracket (Active-ECS) release a nut of fastening of an air-line to the top part of a rack. You will throw out a sealing ring, - it is subject to replacement without fail. Turn out fixing bolts and remove the Active-ECS actuation mechanism from the top part of a rack, - do not forget to disconnect an electrical wiring.
6. Turn out a bolt of the lower support of the shock-absorber. Give nuts of fastening of the top plate of the shock-absorber to a body element.
7. Lower the jack which is propping up the lower lever, remove a rack and take it from under the car.

1. Fill the top plate of a screw spring on the regular place and install a rack on the car, - use a jack.
2. Tighten the top fixing nuts with the required effort (45 H • м).
3. The lower bolt tighten with effort 98 H • m.
4. On models with Active-ECS connect е to a rack an air-line, - do not forget to replace a sealing ring. Tighten a nipple nut with the required effort (9 H • м).
5. Install the Active-ECS actuation mechanism on a rack, connect to it an electrical wiring and fix by bolts.
6. Remove a jack, establish wheels and lower the car on the earth.
7. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Slightly prop up the torsion beam and the lever, - track that the jack did not concern a cross jet bar.

Between a head of a jack and a beam of the bridge it is necessary to lay surely wooden whetstone, you get a jack under the central part of a beam.

4. For the purpose of ensuring access to the top fixing nuts remove the corresponding elements of an upholstery of the luggage compartment.
5. On models with an active suspension bracket (Active-ECS) mark and disconnect air-lines from the top part of the shock-absorber. At once to a zakuporta the open ends of tubes and unions in order to avoid hit in system of dirt. Try not to allow twistings and bending of tubes. Remove a sealing ring and the plug. Remove assembly of the actuation mechanism.
6. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
7. Turn out the lower fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the lower fixing bolt.
2. Poddomkratte a beam of the back bridge, trying to obtain hit of fixing hairpins of the top support of the shock-absorber in reception openings. Record a rack in the top situation.
3. Screw fixing nuts on hairpins and tighten them with the required effort (40 H • м).
4. Lower the car on the earth and finally tighten the lower bolt of fastening of the shock-absorber with the required effort (100 H • м).
5. On models with an active suspension bracket install into place the Active-ECS components and restore initial connection of air-lines, - do not forget to replace sealing rings. Tighten a lock-nut with effort 9 H • m. Moisten the nipple socket with soap water, start the engine and check connection for existence of signs of leak of air. In case of need replace a sealing ring.
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of the luggage compartment.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Slightly prop up a jack the longitudinal lever of a suspension bracket.
4. For the purpose of ensuring access to the top fixing nuts remove the corresponding elements of an upholstery of the luggage compartment.
5. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
6. Give a bolt of fastening of a basic arm of a brake hose.
7. Turn out the lower fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the lower fixing bolt.
2. Poddomkratte the longitudinal lever, trying to obtain hit of fixing hairpins of the top support of the shock-absorber in reception openings. Record a rack in the top situation.
3. Screw fixing nuts on hairpins and tighten them with the required effort (40 H • м).
4. Lower the car on the earth and finally tighten the lower bolt of fastening of the shock-absorber with the required effort (90 ÷ 110 H • м).
5. Establish a basic arm of a brake hose and tighten a bolt of its fastening with the required effort (17 H • м).
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of the luggage compartment.

1. The car also establish to Poddomkratta it on props.
2. Slightly prop up a jack the lower operating suspension bracket lever.
3. For the purpose of ensuring access to the top fixing nuts delay outside a stopper of a back seat, lift and remove a pillow. Turn out fixing bolts and remove a seatback.

4. Give the top nuts of fastening of the shock-absorber.

5. Turn out the lower fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the lower fixing bolt.
2. Poddomkratte a beam of the back bridge, trying to obtain hit of fixing hairpins of the top support of the shock-absorber in reception openings. Record a rack in the top situation.
3. Screw on hairpins of a nut and tighten them with the required effort (44 H • м).
4. Lower the car on the earth and finally tighten the lower bolt of fastening of the shock-absorber with the required effort (98 H • м).
5. Install into place components of a back seat.

1. For the purpose of ensuring access to the top fixing nuts remove the corresponding elements of an upholstery of the luggage compartment.
2. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
3. The car also establish to Poddomkratta it on props.
4. Slightly prop up a jack the longitudinal lever of a suspension bracket.
5. Mark the adjusting provision of the top plate of a spring concerning the chassis, then give fixing nuts.
6. Turn out the lower fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the lower fixing bolt.
2. Poddomkratte the longitudinal lever, trying to obtain hit of fixing hairpins of the top support of the shock-absorber in reception openings. Record a rack in the top situation.
3. Screw fixing nuts on hairpins and tighten them with the required effort (27 H • м).
4. Lower the car on the earth and finally tighten the lower bolt of fastening of the shock-absorber with the required effort (90 H • м).
5. Establish a basic arm of a brake hose and tighten a bolt of its fastening with the required effort (17 H • м).
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of the luggage compartment.