1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Remove racks of the stabilizer of cross stability or bolts of its fastening to the lower lever of a suspension bracket. At the corresponding complete set remove basic cups / plugs.
4. By means of a special stripper like MB9f35 release a finger of a spherical support from a fist of stupichny assembly - if the support is subject to further use, act extremely carefully.
5. Give internal bolts and a nut of fastening of the lower lever of a suspension bracket.
6. Turn out back bolts and, - at the corresponding complete set, - remove a fixing collar.
7. Remove the lever from the car.
8. In case of need remove the plug from a back rod.

1. If removed, install the plug on the lever.
2. Start assembly of the lever on the regular place and fix it by internal bolts. Screw and temporarily tighten a new nut.
3. Establish a back fixing collar, screw bolts. Tighten new nuts of fastening of a collar with the required effort (47 H • l) temporarily tighten a collar bolt, - final tightening of a bolt with the required effort (100 H • l) it is made after lowering of the car on the earth.
4. Press spherical in a fist of stupichny assembly and fix it by a new nut, having tightened the last with effort 60 ÷ 72 H • m.
5. Establish a bar of the stabilizer of cross stability with the racks.
6. Lower the car on the earth and make final tightening of nuts of internal bolts of fastening of the lever with effort 120 H • ми a collar bolt (100 H • м).
7. Make sure of reliability of tightening of fixture of elements of a suspension bracket.
8. Connect a negative wire to the battery.

1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. On models with ABS remove basic arms of an electrical wiring of the wheel sensor from assembly of the lower managing director of the lever.

3. Remove a through bolt of fastening lower to the operating lever of a fist of stupichny assembly.

4. Remove a bolt of fastening of the lower managing director of the lever to a suspension bracket beam.

5. Remove the lever from the car.

1. Connect the lever to a beam of a suspension bracket and temporarily tighten a nut of a fixing bolt.
2. Connect the lever to a fist of stupichny assembly, - also temporarily tighten to a hook of a through bolt.
3. Connect a rack of the stabilizer of cross stability to the lever. Tighten a fixing nut with the required effort (39 H • м).
4. Establish a wheel and lower the car on the earth.
5. Make final tightening of nuts of both fixing bolts with the required effort (98 H • м).
6. Check the angles of installation of back wheels, in case of need make the corresponding adjustment.

1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. Mark the provision of an adjusting bolt.

3. By means of a stripper of the MB991113 type release a finger of a spherical support from a fist of stupichny assembly.

4. Give bolts of fastening of the lever to a beam of a suspension bracket and remove lever assembly from the car.

1. Connect the lever to a suspension bracket beam, achieve combination of adjusting tags of an adjusting bolt, then temporarily tighten a nut of a fixing bolt.
2. Press a finger of a spherical support in a fist of stupichny assembly, tighten with the required effort (28 H • l) a fixing nut.
3. Establish a wheel and lower the car on the earth.
4. Finally tighten with the required effort (69 ÷ 78 H • l) bolted couple of fastening of the lever on a suspension bracket beam
5. Check the angles of installation of back wheels, in case of need make the corresponding adjustment.

1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. Mark the provision of an adjusting bolt.
3. On models with an active suspension bracket (Active-ECS) disconnect a rod of the sensor of height of a road gleam from assembly of the lower lever.
4. Prop up the longitudinal lever of a suspension bracket a jack and thaw самоконтрящуюся a nut of fastening of the lower lever to the longitudinal lever.
5. Disconnect lever assembly from a beam of a suspension bracket and remove it from the car.

1. Connect the lever to a suspension bracket beam, achieve combination of adjusting tags of an adjusting bolt, then temporarily tighten a nut of a fixing bolt.
2. Connect assembly to the longitudinal lever and tighten самоконтрящуюся a nut with the required effort (75 ÷ 89 H • м).
3. On models with an active suspension bracket connect a rod of the sensor of height of a road gleam to the lever.
4. Establish a wheel and lower the car on the earth.
5. Finally tighten with the required effort (75 ÷ 89 H • l) bolted couple of fastening of the lever on a suspension bracket beam
6. Check the angles of installation of back wheels, in case of need make the corresponding adjustment.