12:18. Removal and installation of a steering wheel

The Mirage models for 1993 the issue.

Removal

 PERFORMANCE ORDER

1. Bring forward wheels of the car into rectilinear situation. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove an overlay of the button of activation of a horn from a stupichny part of a steering wheel, - delay bottom edge of a slip up, then disconnect an electrical wiring.
3. Give a nut of fastening of a steering wheel.
4. Mark the provision of a wheel of rather steering shaft.
5. By means of a special stripper remove a wheel from a steering column.

Do not make at all attempts to bring down a wheel from a shaft by means of the hammer!


Installation

 PERFORMANCE ORDER

1. Watching correctness of combination of the adjusting tags put in the course of dismantle, put a wheel on a shaft of a steering column.
2. Screw a fixing nut and tighten it with the required effort ( 40 H • м).
3. Connect an electrical wiring and establish an overlay of activation of a horn on a stupichny part of a steering wheel.
4. Connect a negative wire to the battery.


The Galant models for 1993 the issue.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove an overlay of activation of a horn: on models for 1991 the issue a slip should be wrung out for the purpose of release it from clamps up, to lift and disconnect an electrical wiring; on models 1992 ÷ of 1993 of the issue previously to turn out the screw located in the lower part of a slip.
3. Give a fixing nut.
4. Mark the provision of a wheel of rather steering shaft.
5. By means of a special stripper remove a wheel from a steering column.

Do not make at all attempts to bring down a wheel from a shaft by means of the hammer!


Installation

 PERFORMANCE ORDER

1. Watching correctness of combination of the adjusting tags put in the course of dismantle, put a wheel on a shaft of a steering column.
2. Screw a fixing nut and tighten it with the required effort (35 ÷ 45 H • м).
3. Connect an electrical wiring and establish an overlay of activation of a horn on a stupichny part of a steering wheel.
4. Connect a negative wire to the battery.


The Galant and Mirage models since 1994 of the issue.

Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid getting injured at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation. In order to avoid damage of the SRS system, track that the steering shaft was not turned after removal of a steering wheel. Block a column the ignition key at the rectilinear provision of forward wheels.


Removal

 PERFORMANCE ORDER

1. Bring forward wheels of the car into rectilinear situation.
2. Make SRS deactivation (see the Head Onboard electric equipment).

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Having hooked, remove side plastic covers and give the screws of fastening of the module of a safety cushion located under assembly of a steering wheel.

4. For a detachment of the socket of a spring contact drum of a safety cushion release a clamp, having wrung out it towards the module. Holding a clamp wrung out, accurately hook the socket the suitable tool and disconnect it from the module.

5. Remove the module of a safety cushion and lay it a cover up transfer it to a pure dry surface.

6. Mark the provision of a steering wheel concerning a column shaft.
7. Give a fixing nut and remove a wheel, having used a suitable stripper, - at all do not make attempts to bring down a wheel from a shaft by means of the hammer!

In order to avoid violation of centering of the contact SRS cable reel do not allow a provorachivaniye of a steering shaft at the removed steering wheel. At the compelled violation of this requirement the drum has to be centered before installation of a wheel into place.



Installation

 PERFORMANCE ORDER

1. Make sure that forward wheels of the car remain in rectilinear situation. In case of need make centering of a spring contact drum of a safety cushion, - achieve combination of a tag of NEUTRAL with the response index on a casing.
2. Put a steering wheel on a column shaft, - track correctness of combination of the tags put in the course of dismantle. Screw a fixing nut and tighten it with the required effort (40 H • м).
3. Install the safety cushion module.
4. Connect a negative wire to the battery, turn the ignition key in position of ON, - on the dashboard the control lamp of SRS has to join for seven seconds.


Diamante models

Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid getting injured at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation. In order to avoid damage of the SRS system, track that the steering shaft was not turned after removal of a steering wheel. Block a column the ignition key at the rectilinear provision of forward wheels.


Removal

 PERFORMANCE ORDER

1. Bring forward wheels of the car into rectilinear situation.
2. Make SRS deactivation (see the Head Onboard electric equipment).

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Give the nuts of fastening of the module of a safety cushion located under assembly of a steering wheel.
4. For a detachment of the socket of a spring contact drum of a safety cushion release a clamp, having wrung out it towards the module. Holding a clamp wrung out, accurately hook the socket the suitable tool and disconnect it from the module.
5. Remove the module of a safety cushion and lay it a cover up transfer it to a pure dry surface.
6. Mark the provision of a steering wheel concerning a column shaft.
7. Give a fixing nut and remove a wheel, having used a suitable stripper, - at all do not make attempts to bring down a wheel from a shaft by means of the hammer!

In order to avoid violation of centering of the contact plentiful SRS reel do not allow a provorachivaniye of a steering shaft at the removed steering wheel. At the compelled violation of this requirement the drum has to be centered before installation of a wheel into place.


Installation

 PERFORMANCE ORDER

1. Make sure that forward wheels of the car remain in rectilinear situation. In case of need make centering of a spring contact drum of a safety cushion, - achieve combination of a tag of NEUTRAL with the response index on a casing.
2. Put a steering wheel on a column shaft, - track correctness of combination of the tags put in the course of dismantle. Screw a fixing nut and tighten it with the required effort (40 H • м: for models 1992 ÷ of 1993 of the issue and 45 H • м: for models since 1994 of the issue).
3. Install the module of a safety cushion and tighten nuts of its fastening with the required effort (5 H • м).
4. Connect a negative wire to the battery, turn the ignition key in position of ON, - on the dashboard the control lamp of SRS has to join for seven seconds.