1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Sort racks of the stabilizer of cross stability: give lock-nuts, take cups, rubber and plugs. Turn out bolts of fastening of racks.
4. Remove a reception pipe of system of production of the fulfilled gases.
5. Hang out the power unit on the winch from above. Turn out four bolts of fastening of the central beam.
6. Remove both support of assembly of the rack mechanism of the steering drive.
7. Disconnect the lower lever of a suspension bracket from the central beam.
8. Prop up a beam a jack, turn out fixing bolts and omit assembly, having provided necessary free space for extraction of a bar of the stabilizer of cross stability.
9. Give fixture and take a bar of the stabilizer of cross stability from under the car.

1. Installation is made upside-down.
2. Tighten bolts of fixing collars of a bar of the stabilizer of cross stability with effort 22 H • m.
3. At assembly of racks of the stabilizer track that the size of a vystupaniye of a bolt made 22 mm.
4. Lower the car on the earth and connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Disconnect a reception pipe of system of production of the fulfilled gases from a final collector (remove sealing laying). Tie up a pipe so that it did not prevent dismantle of the stabilizer of cross stability.

Try not to allow bending of the flexible coupling of reception section of a final path at an angle more than in several degrees!

4. Turn out back bolts of fastening of the central beam.
5. Turn out bolts of fastening of racks of the stabilizer of cross stability.

On racks of spherical type in the course of an otpuskaniye самоконтрящейся nuts a sharovy finger should be held from a provorachivaniye by means of a six-sided key.

6. Turn out bolts of fixing collars of a bar of the stabilizer of cross stability.
7. Delay both ends of a bar on the car back, then release its right end from under the lower lever of a suspension bracket. Afterwards release the left end of a bar from under the opposite lever. Having pulled a bar to the right, take it from under the car.
8. Estimate degree of wear of all rubber plugs, replace defective components.
9. Check a condition of a bar of the stabilizer. In case of need make replacement.

1. Get a bar of the stabilizer of cross stability on the regular place.
2. Establish collars of fastening of a bar (pay attention to identification marking). Level components, then strongly tighten fixture.
3. When tightening fixture of racks of spherical type use two keys. Track that bolt vystupaniye size over a nut made 16 ÷ 18 mm.
4. Connect a reception pipe to a final collector (do not forget to replace sealing laying). Tighten самоконтрящиеся joint nuts with the required effort (40 H • м).
5. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Disconnect a reception pipe of system of production of the fulfilled gases from a final collector (remove sealing laying).
3. Remove the central knitsa and assembly of the transfer case.
4. Remove a rack of the stabilizer of cross stability, - at an otdavaniye of nuts spherical hairpins of hinges should be held from a provorachivaniye the second key.
5. Turn out a fixing bolt and remove an assembly collar of the stabilizer of cross stability with the rubber plug.
6. Disconnect the stabilizer from the right lower lever of a suspension bracket.
7. Take the left section of a bar of the stabilizer through space between a power shaft and the lower lever. The right section is taken from under the corresponding lower lever.

1. Establish a stabilizer bar on the regular place.
2. Temporarily tighten fixture of an assembly collar. Level end faces of the rubber plug of the adjusting tags which are rather applied on a bar, then tighten fixture finally.
3. Screw and tighten a bolt of an assembly collar.
4. Establish racks of the stabilizer and tighten their fixing nuts, - spherical hairpins are blocked from a provorachivaniye by means of the second wrench. The bolt has to act over a nut surface at a size of 16 ÷ of 18 mm).
5. Establish assembly of the transfer case and an assembly knitsa.
6. Establish the left lower beam and tighten bolts of its fastening with the required effort (80 H • м: back and 100 H • м: lobbies).

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Release самоконтрящиеся nuts and remove racks of the stabilizer of cross stability.

4. Remove assembly collars of a bar of the stabilizer with rubber plugs.

5. Remove the stabilizer.
6. Estimate degree of wear of components, replace the failed knots.

1. Get a stabilizer bar on the regular place.
2. Freely establish assembly collars.
3. Level a bar so that both of its landing tags appeared at distance about 10 mm from the inside from collars.
4. Tighten bolts of fastening of collars with the required effort (39 H • м).
5. Connect stabilizer racks to a bar and damping forks. Tighten lock nuts with the required effort (39 H • м).
6. Lower the car on the earth and connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props.
3. Remove a reception pipe of system of production of the fulfilled gases and protection of a case.
4. Remove the left and right lower beams.
5. Remove a rack of the stabilizer of cross stability.
6. Release assembly collars and remove a stabilizer bar.

1. Get a stabilizer bar on the regular place and fix it by assembly collars. Do not mix the left collar with right, - attentively study identification marking.

Before installation all rubber components of fixing knots should be greased.

2. Establish a rack of the stabilizer of cross stability.
3. Establish the lower beams.
4. Establish a reception pipe of system of production of the fulfilled gases and elements of protection of a case.
5. Connect a negative wire to the battery.