13:14. Replacement of the antenna of the radio receiver

Details of installation of the antenna of the radio receiver on the Mirage models for 1992 the issue.

1 — the Central section of finishing of the dashboard and a ware box
2 — the Overlay of a threshold
3 — the Overlay of a side fairing
4 — the Air sleeve (models with a back heater)
5 — the Module of management of MPI
6 — the Radio receiver

7 — Cable bindings
8 — Clamps
9 — an antenna Mast
10 — the Nut of fastening of the basis of the antenna
11 — the antenna Basis


Details of installation of the antenna of the radio receiver on the Mirage models since 1993 of the issue.

1 — an antenna Mast
2 — the Knee emphasis
3 — the Central section of finishing of the dashboard
4 — the Radio tape recorder

5 — the Overlay of a side fairing
6 — the Clamp
7 — the Antenna cable
8 — the antenna Basis


Details of installation of the antenna of the radio receiver on the Galant models

Stationary antenna

1 — the Panel of a side upholstery of the luggage compartment
2 — an antenna Mast
3 — the Ring nut
4 — the Contact socket of an antenna cable

Electrodriving antenna

1 — the Panel of a side upholstery of the luggage compartment

2 — the Ring nut
3 — the electrical wiring Socket
4 — the Contact socket of an antenna cable
5 — the Driving electric motor


Details of installation of the antenna of the radio receiver on the Diamante models

1 — the Ring nut
2 — the antenna Basis
3 — the Contact socket of an electrical wiring and antenna cable
4 — Assembly of a driving electric motor

5 — the Radio tape recorder
6 — the Glass antenna with the contact socket of an antenna cable
7 — the Antenna cable


Replacement of a mast of the antenna can be made by its simple reversing from the basis. The description of the procedure of replacement of the basis assembled with an antenna cable is given below.


The Mirage models for 1992 the issue.

Removal

 PERFORMANCE ORDER

1. Details of installation of the antenna of the radio receiver on the Mirage models for 1992 are shown to the issue on an illustration.
2. The car also establish to Poddomkratta it on props.
3. Remove the right forward wheel.
4. Remove a loker of protection of a wheel arch.
5. For the purpose of ensuring access to the radio receiver remove the central section of finishing of the dashboard and a ware box.
6. Remove overlays of a threshold of the right forward door of the car.
7. On models with a back heater remove the air duct laid under a ware box.
8. Accurately remove PCM (see the Head of the Control system of the engine).
9. Remove the radio receiver and disconnect from it an antenna cable.
10. Release a cable from intermediate bindings and clamps of its fastening under the dashboard.
11. Turn out an antenna mast from assembly of its basis.
12. Give the top nut of fastening of the basis of the antenna (on a car wing) and release the lower bolt of fastening of a mast.
13. Remove a mast and accurately release an antenna cable.


Installation

 PERFORMANCE ORDER

1. Fill in an opening in a wing replaceable antenna assembly and strongly tighten the top nut and the lower bolt.
2. Carefully get a cable under the dashboard on connect it to the radio receiver, - track reliability of fastening of a cable in all provided clamps and bindings.
3. Install into place the module of management of MPI.
4. If removed, establish into place an air sleeve of a heater.
5. Establish overlays of a threshold of the right forward door.
6. Establish a ware box.
7. Establish the central section of finishing of the dashboard.
8. Establish a loker of protection of a wheel arch.
9. Establish a wheel and lower the car on the earth.


The Mirage models since 1993 of the issue.

Removal

 PERFORMANCE ORDER

1. Details of installation of the antenna of the radio receiver on the Mirage models since 1993 are shown to the issue on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Turn out screws of fastening of the basis of the antenna.
4. Lift an antenna mast assembled with the basis and separate it from a car roof.
5. Disconnect an antenna cable.


Installation

 PERFORMANCE ORDER

Installation is made upside-down.


Galant and Diamante models

Removal

 PERFORMANCE ORDER

1. Details of installation of the antenna of the radio receiver on the Galant and Diamante models are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Remove the side panel of an upholstery of the luggage compartment.
4. On models with the stationary antenna turn out a mast.
5. Accurately release the ring nut established from above on a car wing.
6. Disconnect an electrical wiring from a driving electric motor. Disconnect an antenna cable.
7. Give fixing bolts and nuts and remove assembly of an electric motor of the drive of the antenna.


Installation

 PERFORMANCE ORDER

1. Establish a driving electric motor and tighten elements of its fixture.
2. Restore initial connection of an electrical wiring and antenna cable.
3. Screw a ring nut and accurately tighten it with the required effort (4 H • the m, - is slightly stronger, than by hand).
4. On models with the stationary antenna screw a mast.
5. Install the side panel of an upholstery of the luggage compartment.