1. Open a cowl and prop up it in open situation.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Having turned clockwise and having pulled outside, uncover a lamp holder.

4. Carefully turning counterclockwise, take from a headlight casing a cartridge with a lamp.

5. Holding a lamp for a socle, release it from the boss.

1. Holding a lamp for a socle, accurately fill it in a cartridge.
2. Put assembly in a casing of a block headlight and, having turned, reliably block it.
3. Having pressed and having turned counterclockwise, establish into place a protective cover of a lamp holder. Make sure of reliability of landing of a cover in order to avoid hit in assembly of moisture or violation of focusing of light beams.
4. Connect a negative wire to the battery and check serviceability of functioning of head headlights.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove the limiting access to the corresponding lamp components.

3. Turn a lamp holder counterclockwise and take it from the seat.

4. For release of a lamp from the boss pull it along the axis.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Turn out two screws of fastening of a lens of the index of turn.

3. Release assembly of the index from the body panel.

4. Turn a lamp holder counterclockwise and take it from assembly of the index.

5. For release of a lamp from the boss pull it along the axis.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Open a door a back/cover of the luggage compartment. Disconnect the corresponding electrical wiring, release clamps and remove the back panel of finishing of assembly of the corresponding back combined lamp.

3. Having turned, release the corresponding lamp holder from a casing of lantern assembly.

4. For release of a lamp from the boss press it down and turn on 1/8 turns counterclockwise. Having pulled, take a lamp from a lamp holder.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Open a cover of the luggage compartment.

3. At the corresponding complete set remove the finishing panel installed from the inside of a cover of the luggage compartment.

4. Turn a lamp holder on 1/4 turns counterclockwise and release it from assembly of the corresponding lamp.

5. For release of a lamp from the boss pull it along the axis.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Turn out two fixing screws and remove assembly of the corresponding lamp from the body panel of the car.

2. Turn a lamp holder counterclockwise and release it from lantern assembly.

3. For release of a lamp from the boss pull it along the axis.

Installation is made upside-down.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Open a cover of the luggage compartment and disconnect an electrical wiring from assembly of a stoplight of the top level, - access to a stoplight opens from under the back saloon shelf.

3. Turn out fixing screws and take a lamp holder from assembly of a stoplight.

4. Having slightly pressed, turn a lamp clockwise and release a lamp from the boss.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. On the Mirage and Galant models release square clamps or fixing bolts and uncover with assemblies a stoplight top the level.
3. On the Diamante models for removal of a cover it is necessary to wring out accurately in its side which.
4. Press a lamp inside, turn it clockwise and take from the boss of a lamp holder.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Open a cover of the luggage compartment and disconnect an electrical wiring from assembly of a stoplight of the top level, - access to a stoplight opens from under the back saloon shelf.
3. Turn a lamp holder counterclockwise and release it from lantern assembly.
4. Having slightly pressed, turn a lamp clockwise and release a lamp from the boss.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Turn out two screws of fastening of a lens of a lamp of illumination of registration plate.

3. Remove a lens from a back wall of a cover of the luggage compartment.

4. Having pulled on itself, take a lamp from the boss of a lamp holder.

Installation is made upside-down. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.

1. Having accurately hooked the small screw-driver, remove a plafond of the corresponding lamp.

2. Release a lamp from spring contacts. If the lamp is equipped with cone-shaped socles, slightly wring out a lock clamp / a contact spring.

1. Check a condition of working surfaces of contacts, in case of need make their cleaning.
2. Installation is made upside-down. Track reliability of fixing of a lamp in the boss.
3. In conclusion make sure of serviceability of functioning of lamps, then establish into place a plafond.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove a combination of devices (see the Section Removal and installation of a combination of devices).

3. Turn a lamp holder of the lamp needing replacement counterclockwise and remove it from assembly of a combination of devices.

4. For release of a lamp from the boss pull it along the axis.

2. Do not forget to connect a negative wire to the battery and to check serviceability of functioning of lighting fixtures.