6.5. Check of a state and replacement of fuel lines and their nipple connections

Remember that gasoline is extremely flammable liquid! During the work with components of a power supply system observe all taken measures of fire safety. Do not smoke! Do not approach the venue of works with naked flame or the carrying unprotected by the lamp shade! You do not make service of system in the rooms equipped with the heating devices using natural gas and equipped with a control torch (such as vodogre and dryers for clothes). Do not forget that gasoline is among cancerogenic substances, i.e., - the substances promoting development of cancer! Try not to allow hits of fuel on open parts of the body, use rubber protective gloves, at casual unforeseen contact with fuel carefully wash out hands warm water with soap. Immediately collect the spilled fuel and do not put the rags impregnated with fuel and lubricants near sources of naked flame. Remember that the power supply system of the models equipped with injection of fuel constantly is under pressure. Before starting a detachment of fuel lines, dump residual pressure in system. At service of components of a power supply system put on goggles. Constantly hold near at hand the class B fire extinguisher!


 PERFORMANCE ORDER

1. Lines of a fuel path of a power supply system are laid between a gasoline tank and a motive compartment. Steel tubes and flexible fuel hoses fasten to the car bottom by means of clips and screw fixture. Every time when the car rises above the ground with any purpose (for example, for survey or replacement of components of system of production of the fulfilled gases), try to take an opportunity and to check a condition of fuel lines and their nipple connections.
2. Attentively examine all hoses and tubes of a fuel path on existence of cracks, twisting, deformations and other mechanical damages.
3. At identification of signs of internal pollution or violation of passability the corresponding section of a fuel path needs to be removed and blown compressed air.
4. Make sure of reliability of delay in all nipple connections of hoses and metal tubes of a fuel path.


Steel tubes

 PERFORMANCE ORDER

1. Use only high-strength steel tubes of production of the proved manufacturers as replaceable sections.
2. Remember that copper and aluminum tubes are not capable to sustain the vibration loadings arising in use the car.
3. Do not forget that fuel lines on the models equipped with system of injection have to maintain high internal pressure.
4. Often in company shops of automobile accessories it is possible to get the sections of metal tubes equipped with carving nipple nozzles. During the easing and delay in nipple connections use two wrenches to avoid a provorachivaniye of a reciprocal part of the socket. Without fail check a condition of the nipple connections of sealing rings used for sealing. At once replace the worn-out or mechanically damaged rings. Try to use only company details as replaceable components.


Flexible hoses

 PERFORMANCE ORDER

When replacing fuel hoses use only company components calculated on high internal pressure.

Flexible fuel hoses have to be laid not closer than in 10 cm from components of system of production of the fulfilled gases and are not closer than in 25 cm from the catalytic converter. You watch that fuel lines did not adjoin to body elements and components of a suspension bracket. The minimum admissible size of a gap makes 6.3 mm.


Replacement

 PERFORMANCE ORDER

1. Dump pressure in a power supply system (see the Section Dropping Pressure in a power supply system).
2. Release the section of a fuel path which is subject to dismantle from intermediate clamps of fastening it to the car bottom.
3. In most cases flexible hoses fasten to metal lines by means of collars of spring type. For an otpuskaniye of a collar squeeze it flat-nose pliers and shift up a hose. The collar deformed at an otpuskaniye is not subject to reuse and has to be replaced. Track that at connection the hose was tense on a tube at least on 2.5 cm, establish by the correct image a fixing collar.
4. In some nipple knots sockets of bystry joining are used, - for an otpuskaniye of such socket it is necessary to squeeze his lock uvulas and to pull the connected lines in different directions.

Needlessly do not pick up the socket case from a nipple part of the metal phone as it leads to easing of the holding effort developed by it.

5. Installation is made upside-down. On sockets of bystry joining track a zashchelkivaniye of both lock uvulas in reception flutes.


Repair

 PERFORMANCE ORDER

In case of damage of the metal or flexible fuel line the failed section should be replaced only company the corresponding standard size.