3726b8fd

11:11. Replacement of blocks of disk brake mechanisms

Design of the disk brake mechanism of a forward wheel of the Mirage models (for the Galant models for 1993 the issue the similar picture takes place)

1 — the Brake hose
2 — Sealing washers

3 — the Support
4 — the Brake disk


Design of the disk brake mechanism of a back wheel of the Mirage models (for the Galant models for 1993 the issue the similar picture takes place)

1 — the Cable of the drive of the parking brake
2 — the Brake hose
3 — Assembly of a support
4 — the Brake disk
5 — the Cover of a stupichny nut

6 — Stupichnaya a nut
7 — Stupichnaya assembly
8 — the Brake board
9 — the Arm


Design of the two-cylinder disk brake mechanism of a forward wheel of the Diamante models

1 — the Directing finger
2 — the Blocking finger
3 — the Plug
4 — the Anchor bracket
5 — the Protective cover
6 — the Lock ring
7 — the Boot

8 — the Piston
9 — the Cuff
10 — the Support
11 — Assembly of a block with the indicator of wear of a frictional slip
12 — the Brake shoe
13 — External adjusting laying
14 — the Spring clamp


Design of the disk brake mechanism of a back wheel of the Galant 1994 ÷ models of 1995 of the issue.

1 — the Brake hose
2 — Assembly of a support

3 — the Brake disk


Design of the disk brake mechanism of a forward wheel of the Galant models since 1996 of the issue.

1 — the Hollow bolt of nipple connection of a brake hose
2 — Sealing washers

3 — Assembly of a support
4 — the Brake disk


Replacement of brake shoes has to be made at the same time on both forward/back brake mechanisms. Remember that the dust produced in the course of operation of brake mechanisms may contain extremely unhealthy asbestos of the person. Do not blow off dust compressed air at all and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. Do not use for rubbing of components of the brake system gasoline or solvents on an oil basis at all, - apply only company cleaners or methyl alcohol!


The Mirage and Galant models for 1993 the issue.

Brake mechanisms of forward wheels

Removal

 PERFORMANCE ORDER

1. The design of the disk brake mechanism of a forward wheel for the Mirage and Galant models for 1993 is presented to the issue on an illustration.
2. Pump out a part of liquid from the GTTs tank. The tank has to be devastated approximately half for the purpose of providing a stock of volume for rise in level at push-up of blocks.
3. Weaken nuts of fastening of forward wheels. A car front also establish to Poddomkratta it on props, cock a parking brake / prop up antiretractable boots back wheels.
4. Take the directing fingers of a support and lift assembly of the last, having removed it from an anchor bracket of the brake mechanism. Tie up a support in the lifted situation a wire, without allowing hang it on a brake hose.

On some models the support can be recorded in the lifted situation by extraction of only one of the directing fingers, - the second will play at the same time a role of a rotary axis.

5. Remove brake shoes with spring clamps and adjusting laying, - try to remember an order of installation of components.
6. For the purpose of fixing of a brake disk on stupichny assembly screw couple of wheel nuts on hairpins and freely bring up them.


Installation

 PERFORMANCE ORDER

1. By means of a big clamp wring out the support piston in the cylinder (on two-cylinder supports it is necessary to drown both pistons).
2. Grease the sliding basic surfaces of the brake mechanism and establish replaceable brake shoes, in the correct order having placed adjusting laying and spring clamps. Lower a support on an anchor bracket, - try not to allow a latching of a protective cover, track that the brake hose was not overwound.
3. Grease, establish on the regular places and tighten the directing and blocking fingers.
4. Establish a wheel and lower the car on the earth.
5. Check efficiency of functioning of the brake system, - before starting trial runs several times squeeze out a pedal of a foot brake for the purpose of shrinkage of components and rise in pressure in a hydraulic path.


Brake mechanisms of back wheels

Removal

 PERFORMANCE ORDER

1. The design of disk brake mechanisms of back wheels on the Mirage and Galant models for 1993 is presented to the issue on an illustration.
2. Pump out about 2/3 brake fluids from the GTTs tank, - at push-up of the piston level liquid can begin to be forced out from the tank.
3. The car also establish to Poddomkratta it on props.
4. Remove the corresponding back wheel.
5. Release the parking brake.
6. Disconnect a driving cable of the parking brake from assembly of the brake mechanism.
7. Take the lower directing finger, lift assembly of a support up and tie up in this situation.
8. Remove external adjusting laying, brake shoes and spring clamps, - try to remember the adjusting provision of components.
9. For the purpose of fixing of a brake disk on stupichny assembly screw couple of wheel nuts on hairpins and freely bring up them.


Installation

 PERFORMANCE ORDER

1. Rotating a support clockwise by means of special adaptation No. MB9f52, drown it in the cylinder.
2. Grease the sliding basic surfaces of the brake mechanism and establish replaceable brake shoes, in the correct order having placed adjusting laying and spring clamps.
3. Lower a support on an anchor bracket, - try not to allow a latching of a protective cover, track that the brake hose was not overwound.
4. Grease, establish on the regular place and tighten the lower directing finger.
5. Establish a wheel and lower the car on the earth.
6. Check efficiency of functioning of the brake system, - before starting trial runs several times squeeze out a pedal of a foot brake for the purpose of shrinkage of components and rise in pressure in a hydraulic path.


The Diamante and Galant models since 1994 of the issue.

Brake mechanisms of forward and back wheels

In view of the fact that on these models disk brake mechanisms of back wheels are not equipped with the drive of the parking brake, they do not differ on a design from lobbies and are considered together.


Removal

 PERFORMANCE ORDER

1. The design of disk brake mechanisms on the Diamante and Galant models since 1994 is presented to the issue on illustrations.
2. Pump out about 2/3 brake fluids from the GTTs tank, - at push-up of the piston level liquid can begin to be forced out from the tank.
3. The car also establish to Poddomkratta it on props.
4. Remove the corresponding wheel.

5. Take the directing and blocking fingers, then remove a support from an anchor bracket and tie up it a wire, avoiding a tension of a flexible brake hose.

On some models the support can be recorded in the lifted situation by leaving on the place and uses as a rotary axis of the top finger.

6. Remove brake shoes with spring clamps and adjusting laying, - try to remember an order of installation of components.

7. For the purpose of fixing of a brake disk on stupichny assembly screw couple of wheel nuts on hairpins and freely bring up them.


Installation

 PERFORMANCE ORDER

1. By means of special adaptation or a big clamp wring out the support piston in the cylinder.

2. Grease the sliding basic surfaces of the brake mechanism and establish replaceable brake shoes, in the correct order having placed adjusting laying and spring clamps. Lower a support on an anchor bracket, - try not to allow a latching of a protective cover, track that the brake hose was not overwound.

3. Grease, establish on the regular places and tighten the directing and blocking fingers. The effort of tightening of the directing and blocking fingers makes 75 H • m for forward brake mechanisms and 27 H • m - for back.

4. Establish a wheel and lower the car on the earth.
5. Check efficiency of functioning of the brake system, - before starting trial runs several times squeeze out a pedal of a foot brake for the purpose of shrinkage of components and rise in pressure in a hydraulic path.