11:16. Removal, installation and check of a condition of the brake drum

Design of the drum brake mechanism used on the Mirage models for 1992 by the issue.

1 — the Cover of a stupichny nut
2 — Stupichnaya a nut
3 — the Internal holder of the external bearing
4 — the Brake drum
5 — Pruzhina of fastening of a boot to the regulator lever
6 — the regulator Lever
7 — Assembly of the automatic regulator
8 — the Lower coupling spring
9 — Plates of the directing springs
10 — the Directing springs of boots
11 — the Top coupling spring

12 — the Brake boot
13 — Assembly of a boot with anchor knot
14 — the Holder
15 — the Wavy washer
16 — the Executive lever of the drive of the parking brake
17 — the Brake boot
18 — the Anchor finger
19 — the Brake tube
20 — the Lock ring
21 — the Brake board


Design of the drum brake mechanism used on the Galant and Mirage models since 1993 by the issue.

1 — the Brake drum
2 — Pruzhina of fastening of a boot to the regulator lever
3 — the regulator Lever
4 — Assembly of the automatic regulator
5 — the Lower coupling spring
6 — Plates of the directing springs
7 — the Directing springs of boots
8 — Plates of the directing springs
9 — the Top coupling spring
10 — the Brake boot with a frictional slip

11 — Assembly of a brake boot with the adjusting lever
12 — the Holder
13 — the Wavy washer
14 — the Executive lever of the drive of the parking brake
15 — the Brake boot with a frictional slip
16 — the Anchor finger
17 — the Brake tube
18 — the Lock ring
19 — Stupichnaya assembly
20 — the Brake board


Remember that the dust produced in the course of operation of brake mechanisms may contain extremely unhealthy asbestos of the person. Do not blow off dust compressed air at all and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. Do not use for rubbing of components of the brake system gasoline or solvents on an oil basis at all, - apply only company cleaners or methyl alcohol!


The Mirage models for 1992 the issue.

Removal

 PERFORMANCE ORDER

1. The design of the drum brake mechanism used on the Mirage models for 1992 by the issue is presented on an illustration.
2. The car also establish to Poddomkratta it on props.
3. Remove the corresponding back wheel.
4. Remove a dustproof cover of a stupichny nut.
5. Give самоконтрящуюся a stupichny nut.
6. Remove the external wheel bearing.
7. Remove from a spindle the brake drum assembled with the internal wheel bearing.
8. Remove an epiploon.


Installation

 PERFORMANCE ORDER

1. For check of the validity to further use самоконтрящейся nuts screw it on a spindle so that the end of the last came to light approximately on 3 mm. Measure torque of resistance to rotation of a nut counterclockwise. The result of measurement makes less than 5.5 H • m, the nut is subject to replacement.
2. Grease and install the internal bearing.
3. Establish a new epiploon.
4. Put on the brake drum a spindle.
5. Grease and install the external wheel bearing.
6. Tighten самоконтрящуюся a stupichny nut with the required effort (150 ÷ 200 H • м).
7. Establish a protective cover.


Check of a state

 PERFORMANCE ORDER

1. Measure the internal diameter of the brake drum removed from the car, - for the purpose of identification of signs of ovality measurement should be performed in several points.

2. If the result of measurement exceeds maximum permissible value (231 mm), replace a drum complete with boots (see the Section Removal and installation of brake boots).


The Galant and Mirage models since 1993 of the issue.

Removal

 PERFORMANCE ORDER

1. The design of the drum brake mechanism used on the Galant and Mirage models since 1993 by the issue is presented on an illustration.
2. The car also establish to Poddomkratta it on props.
3. Remove the corresponding back wheel.
4. Weaken an adjusting nut of the drive of the parking brake.

5. Having pulled on itself, remove the brake drum from stupichny assembly, - in case of need tap assembly by the hammer with soft brisk for the purpose of its release. If the disk at boiled and does not give in to removal, screw in two specially provided carving openings in its front surface couple of bolts suitable by the size and, gradually tightening them, release a drum.


Installation

 PERFORMANCE ORDER

1. Install the reel on a nave.
2. Establish a wheel adjust the drive of the parking brake.
3. Lower the car on the earth.