3726b8fd

11:29. Replacement of rotors of wheel sensors

Rotors of forward sensors

Removal

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.
2. Remove the corresponding wheel.
3. Remove the wheel sensor and, without disconnecting from it an electrical wiring, tie up it aside to suspension bracket elements (do not forget to release an electrical wiring from intermediate clamps).

Do not allow contact of the speaker of the sensitive sensor with rotor teeth!

4. Remove assembly of a forward nave with a rotary fist.
5. Remove a nave from a rotary fist.
6. Clamp a nave in a vice with soft sponges, turn out fixing bolts and remove a rotor of the wheel sensor from assembly.


Installation

 PERFORMANCE ORDER

1. Establish a new rotor on stupichny assembly. Screw fixing bolts and tighten them with the required effort (10 H • м).
2. Establish a nave on a rotary fist.
3. Establish assembly of a rotary fist with a nave on the regular place.
4. Install the wheel sensor.
5. Establish a wheel.
6. Lower the car on the earth.


Rotors of back sensors

All models, except AWD Galant

Removal

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.
2. Remove the corresponding wheel.
3. Remove the wheel sensor and, without disconnecting from it an electrical wiring, tie up it aside to suspension bracket elements (do not forget to release an electrical wiring from intermediate clamps).

Do not allow contact of the speaker of the sensitive sensor with rotor teeth!

4. Remove stupichny assembly.
5. Clamp a nave in a vice with soft sponges, turn out fixing bolts and remove a rotor of the wheel sensor from assembly.


Installation

 PERFORMANCE ORDER

1. Establish a new rotor on stupichny assembly. Screw fixing bolts and tighten them with the required effort (10 H • м).
2. Establish stupichny assembly on the regular place and fix it by the central nut, having tightened the last with the required effort (200 ÷ 260 H • м). Level a nut of rather landing tag and block.
3. Install the wheel sensor.
4. Establish a wheel.
5. Lower the car on the earth.


Galant AWD models

Removal

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.
2. Remove the corresponding wheel.
3. Disconnect a cable of the drive of the parking brake from a support.
4. Remove the wheel sensor assembled with a sealing ring and, without disconnecting from it an electrical wiring, tie up it aside to suspension bracket elements (do not forget to release an electrical wiring from intermediate clamps).

Do not allow contact of the speaker of the sensitive sensor with rotor teeth!

5. Remove a support and a disk of the brake mechanism.
6. Give three bolted couples of fastening of the external end of a power shaft to a connecting flange.
7. Take a shaft aside and tie up it a wire.
8. Give a fixing nut on the back end of the driveshaft, remove a washer. Block a nave from a provorachivaniye by means of the special MB9g67 tool.
9. Remove a connecting flange from assembly of a rotary fist.
10. By means of a stripper, pribolchenny to wheel hairpins, remove assembly of a half shaft.
11. Establish a power shaft on a press (MB9e60), it is reliable упрев a rotor cogwheel in a persistent plate.
12. Squeezing a press, remove a rotor.


Installation

 PERFORMANCE ORDER

1. Napressuyte a rotor on a half shaft (a flute towards a flange).
2. Fill a power shaft in a rotary fist and establish into place a connecting flange.
37 Establish a lock washer and screw a new stupichny nut on a shaft pin. Tighten a nut with the required effort (160 ÷ 220 H • м).
3. Develop a shaft in regular situation and fix it by bolted couples, having tightened nuts of the last with the required effort (61 H • м).
4. Establish into place a brake disk and a support.
5. Install the wheel sensor, - do not forget to replace a sealing ring.
6. Connect a cable of the drive of the parking brake to a support.
7. Establish a wheel and lower the car on the earth.