3726b8fd

12.2. Removal and installation of racks and screw springs of a forward suspension bracket

Details of installation of a rack of a forward suspension bracket on the Mirage models

1 — the Clamp of fastening of a brake hose
2 — the Wheel sensor (models with ABS)
3 — the Bolt of fastening of the lower support (2 pieces)

4 — Samokontryashchayasya a nut
5 — Rack-mount assembly
— Replace N


The Diamante and Galant models on 1993 and since 1999 the issue.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
3. Remove a basic arm of the brake line from a rack, - do not hook a fixing collar any tools!
4. On the models equipped with ABS release a clamp of fastening of the wheel sensor on rack-mount assembly.
5. Prop up a jack the lower lever of a suspension bracket and give bolts of fastening of rack-mount assembly to a rotary fist. Tie up a rotary fist to suspension bracket elements so that not to allow a tension of a brake hose.
6. On models with an active suspension bracket (Active-ECS) release a nut of fastening of an air-line to the top part of a rack. Disconnect the line and remove a sealing ring, then turn out fixing and remove the actuation mechanism of the Active-ECS system from a rack, - do not forget to disconnect an electrical wiring.
7. Mark the provision of the top support of a rack concerning a body, then release fixing nuts and remove rack-mount assembly from the car.


Installation

 PERFORMANCE ORDER

1. Establish rack-mount assembly on the regular place (track correctness of combination of the landing tags put in the course of dismantle), screw the top fixing nuts and tighten them with the required effort (45 H • м).
2. Level a rack and connect it to assembly of a rotary fist, having tightened fixing bolts with the required effort (90 ÷ 105 H • м).
3. On models with an active suspension bracket restore initial connection of an air-line (do not forget to replace a sealing ring) and install into place the Active-ECS actuation mechanism, - do not forget to connect an electrical wiring.
4. Establish into place a basic arm with a brake hose. On models with ABS install the wheel sensor.
5. Establish a wheel and lower the car on the earth.
6. In conclusion execute adjustment of angles of installation of forward wheels.


Mirage models

Removal

 PERFORMANCE ORDER

1. Details of installation of rack-mount assembly on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
4. On the models equipped with ABS release a clamp of fastening of the wheel sensor on rack-mount assembly.
5. Prop up a jack the lower lever of a suspension bracket and give bolts of fastening of rack-mount assembly to a rotary fist.
6. Mark the provision of the top support of a rack concerning a body, then turn out fixing bolts and remove rack-mount assembly from the car.


Installation

 PERFORMANCE ORDER

1. Establish rack-mount assembly on the regular place (track correctness of combination of the landing tags put in the course of dismantle), screw the top fixing nuts and tighten them with the required effort (40 H • м).
2. Level a rack and connect it to assembly of a rotary fist, having tightened fixing bolts with the required effort (110 ÷ 130 H • м).
3. Establish into place a basic arm with a brake hose. On models with ABS install the wheel sensor.
4. Establish a wheel and lower the car on the earth.
5. In conclusion execute adjustment of angles of installation of forward wheels.


Galant 1994 ÷ models of 1998 of the issue.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. The car also establish to Poddomkratta it on props. Remove the corresponding wheel.
3. Disconnect a rack of the stabilizer of cross stability from a damping fork.
4. Turn out lower through and top coupling bolts and remove assembly of a damping fork.

5. Give nuts of fastening of the top support and remove assembly of the shock-absorber with a screw spring from the car.


Installation

 PERFORMANCE ORDER

1. Establish the top support of the shock-absorber, - track correctness of an arrangement of three fixing bolts.
2. Install the rubber plug of the top support, impose a washer, screw a lock-nut and tighten it with the required effort (24 H • м).
3. Install the shock-absorber and tighten the top nuts of its fastening with the required effort (44 H • м).
4. Level a damping fork, establish the lower through bolt of its fastening and tighten its nut with effort 88 H • m. The top coupling bolt tighten with effort 103 H • m.
5. Connect a rack of the stabilizer of cross stability to a damping fork and tighten a nut of its fastening with the required effort (39 H • м).
6. Establish a wheel and lower the car on the earth.
7. In conclusion execute adjustment of angles of installation of forward wheels.