13.9. Removal, installation and adjustment of provision of side doors

Details of installation of side doors on the Mirage models for 1992 the issue.

1 — the Overlay of a threshold
2 — the Side fairing
3 — the Overlay of a threshold
4 — the Decorative overlay of a door pillar
5 — the Contact socket of an electrical wiring
6 — the Sprung pin
7 — Door assembly

8 — the Top loop
9 — the Lower loop
10 — the Limiter of opening of a door
11 — the Drummer
12 — the Adjusting overlay of the drummer
13 — a door sensor switch Cap
14 — the door Sensor switch


Details of installation of side doors on the Galant 1994 ÷ models of 1998 of the issue.

1 — the Contact socket of an electrical wiring
2 — the Sprung pin
3 — Door assembly
4 — the Top loop
5 — the Lower loop

6 — the Limiter of opening of a door
7 — the Drummer
8 — the Adjusting overlay of the drummer
9 — a door sensor switch Cap
10 — the door Sensor switch


Details of installation of side doors on the Diamante models since 1997 of the issue.

1 — the Contact socket of an electrical wiring
2 — the Cover of the limiter of opening of a door
3 — the Bolt
4 — Door assembly
5 — the Top loop
6 — the Lower loop

7 — the Limiter of opening of a door
8 — the Drummer
9 — the Adjusting overlay of the drummer
10 — a door sensor switch Cap
11 — the door Sensor switch


The procedure is identical both for lobbies, and for back side doors of the car.


Removal

 PERFORMANCE ORDER

1. Details of installation of door assemblies are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Open a door and prop up it a cart jack, - for protection of a paint and varnish covering, lay wooden whetstone between a head of a jack and edge of a door.
4. Turn out bolts of fastening of the limiter of opening of a door.
5. Release the carving plug and disconnect a plait of the main braid of an electrical wiring of a door. Disunite other contact sockets of door assembly.
6. Mark the provision of loopy levels of a door.
7. Turn out loopy bolts and accurately remove door assembly, - use the help of the assistant.


Installation

 PERFORMANCE ORDER

1. By means of the assistant establish a door on the regular place, prop up it a jack and by hand tighten bolts of loopy levels.
2. Level loopy levels according to the landing tags put in the course of dismantle, then tighten fixing bolts with the required effort (17 ÷ 26 H • м: for the Galant models for 1993 of the issue and Mirage for 1992 of the issue, 22 H • м: for the models Diamante, Galant since 1994 of the issue and Mirage 1993 ÷ of 1999 of the issue and 27 H • м: for the Mirage models since 1997 of the issue).
3. Restore initial connection of an electrical wiring.
4. Install the limiter of opening of a door and strongly tighten bolts of its fastening.
5. Remove the jack which is propping up a door.
6. Connect a negative wire to the battery.


Adjustment

 PERFORMANCE ORDER

1. Define what bolts from loopy levels need to be released for door shift in the required direction.
2. Release bolts, having provided freedom of movement of door assembly.
3. Correct a door in a body aperture and again tighten fixing bolts with the required effort.
4. Continue implementation of the procedure until the door does not reach required position in a body aperture.
5. Check serviceability of operation of a latch of the lock of a door.
6. In case of need release bolts of fastening of a plate of the drummer and rotation of the last achieve correct operation of a latch.
7. Tighten fixing bolts with the required effort (12 H • м).