4.1.10. Removal and installation of the fan of the cooling system of the engine

Details of installation of ventilatory assemblies on the Diamante models

1 — the Drain gate
2 — a radiator Cover
3 — Pouring a tube
4 — the Broad tank
5 — the Top radiator hose
6 — Nizhny Novgorod a radiator hose
7 — Nipple connection of the line of cooling of ATF
8 — Nipple connection of the line of cooling of ATF

9 — the Pillow of the top support
10 — Assembly of a radiator
11 — the Pillow of the lower support
12 — Assembly of the fan of the condenser of the air conditioning system
13 — the Driving electric motor
14 — Krylchatka
15 — the Driving electric motor
16 — the Casing


Except the Diamante models

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Empty the cooling system.

In order to avoid receiving burns, start performance of the listed works only after final cooling of system! Do not allow hit of antifreeze on open parts of the body and the painted surfaces of the car. Immediately wash away incidentally got splashes a plentiful amount of water. Remember that antifreeze is extremely toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze stored in leaky closed container and immediately collect the cooling liquid spilled on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways utilization of the fulfilled cooling liquid consult at any station of car service. In many regions of the world special points on different reception of working off are equipped. Do not merge old cooling liquid in the sewerage and on the earth at all!

3. Disconnect an overflow tube and the top radiator hose.
4. On models with AT disconnect lines of cooling of ATF (at once to a zakuporta the open ends of hoses and unions).
5. Disconnect an electrical wiring from the engine cooling system fan.
6. Turn out fixing bolts and remove from the car the fan assembled with the protection cover.

7. Release a nut of fastening of a krylchatka and remove the last from a shaft of the driving motor.
8. Turn out fixing screws and remove an electric motor from an assembly casing.


Installation

 PERFORMANCE ORDER

1. Establish an electric motor on an assembly casing, screw and tighten fixing bolts.
2. Further act as it should be, the return to an order of dismantle of components.
3. In conclusion fill in in the cooling system necessary amount of fresh mix (see the Head Nastroyki and routine maintenance), connect a negative wire to the battery and check serviceability of functioning of the fan(s).


Diamante models

Removal

 PERFORMANCE ORDER

1. Details of installation of ventilatory assembly on the Diamante models are presented on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Empty the cooling system.

In order to avoid receiving burns, start performance of the listed works only after final cooling of system! Do not allow hit of antifreeze on open parts of the body and the painted surfaces of the car. Immediately wash away incidentally got splashes a plentiful amount of water. Remember that antifreeze is extremely toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze stored in leaky closed container and immediately collect the cooling liquid spilled on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways utilization of the fulfilled cooling liquid consult at any station of car service. In many regions of the world special points on different reception of working off are equipped. Do not merge old cooling liquid in the sewerage and on the earth at all!

4. Disconnect an electrical wiring from the fan and the radiator sensor.

Usually electric sockets of these components have tight execution, - try not to damage assembly design details.

5. Disconnect the top hose from a radiator and remove a broad tank.
6. Turn out fixing screws and remove ventilatory assembly.

On these models the possibility of removal of fans of the cooling system and air conditioning separately is provided.

7. In case of need dismantle a krylchatka and a driving electric motor.


Installation

 PERFORMANCE ORDER

1. Installation is made as it should be, the return to an order of dismantle of components.
2. In conclusion fill in in the cooling system necessary amount of fresh mix (see the Head Nastroyki and routine maintenance), connect a negative wire to the battery and check serviceability of functioning of the fan(s).