1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. Remove a brake drum / disk (see the Head the Brake system).
3. Remove assembly of a nave with the wheel bearing (see the Section Removal and installation of stupichny assemblies).
4. Prop up a jack a beam of the back bridge.
5. Disconnect the lower support of the shock-absorber from the longitudinal lever.
6. Disconnect the longitudinal lever from a beam of the back bridge.
7. Turn out a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Start assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with the required effort (100 ÷ 120 H • м).
2. Connect the lever to a beam of the back bridge. Tighten a fixing bolt with effort 100 ÷ 120 H • m.
3. Fix the lower support of the shock-absorber on the lever, - tighten fixing with effort 80 ÷ 100 H • м).
4. Remove the jack which is propping up a beam of the back bridge.
5. Establish into place stupichny assembly.
6. Install the brake reel / disk (see the Head the Brake system).
7. Establish a wheel and lower the car on the earth.

1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. Remove a brake drum / disk (see the Head the Brake system).
3. Remove assembly of a nave with the wheel bearing (see the Section Removal and installation of stupichny assemblies).
4. Prop up a jack a beam of the back bridge.
5. Disconnect the lower operating suspension bracket lever from the longitudinal lever.
6. Disconnect the top coupler from the lever.
7. Give a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Start assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with the required effort (100 ÷ 120 H • м).
2. Connect the top coupler to the lever, tighten the fixing boat with effort 90 H • m.
3. Connect the lower operating lever to the longitudinal lever, tighten a fixing bolt with effort 90 H • m.
4. Remove the jack which is propping up a beam of the back bridge.
5. Establish into place stupichny assembly.
6. Install the brake reel / disk (see the Head the Brake system).
7. Establish a wheel and lower the car on the earth.

1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. Prop up a jack a beam of the back bridge.
3. Disconnect the longitudinal lever from a fist of stupichny assembly.
4. Give a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Start assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with the required effort (137 ÷ 157 H • м).
2. Connect the lever to a fist of stupichny assembly, tighten a fixing bolt with effort 118 ÷ 137 H • m.
3. Remove the jack which is propping up a beam of the back bridge.
4. Establish a wheel and lower the car on the earth.

1. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
2. Remove a brake drum / disk (see the Head the Brake system).
3. Remove stupichny assembly (see the Section Removal and installation of stupichny assemblies).
4. Prop up a jack a beam of the back bridge.
5. Disconnect the lower support of the shock-absorber from the longitudinal lever.
6. Disconnect a rack of the stabilizer of cross stability from the lever.
7. Disconnect a tip of cross draft from the lever.
8. Disconnect the lower operating suspension bracket lever from the longitudinal lever.
9. Give a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Start assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with the required effort (140 ÷ 160 H • м).
2. Connect to lever assemblies the lower operating suspension bracket lever, tighten a fixing bolt with the required effort (140 ÷ 160 H • м).
3. Connect a tip of cross thirst to the lever. Tighten a fixing nut with effort 29 H • m.
4. Install a rack of the stabilizer of cross stability on the lever, tighten fixing to a hook with effort 40 H • m.
5. Connect the shock-absorber to the lever. Tighten a fixing bolt with the required effort (90 H • м).
6. Remove the jack which is propping up a beam of the back bridge.
7. Establish into place stupichny assembly.
8. Install the brake reel / disk.
9. Establish a wheel and lower the car on the earth.