3726b8fd

13:17. Removal and installation of the central console

Details of installation of sections of the central console on the Mirage models for 1992 the issue.

1 — the Coin box
2 — the Pocket
3 — the Switch of management of the electric drive of door mirrors / a cap
4 — Facing

5 — Back section of console assembly
6 — the Handle of the lever of gear shifting (RKPP)
7 — Forward section of console assembly


Details of installation of sections of the central console on the Mirage 1993 ÷ models of 1996 of the issue.

1 — the Finishing panel
2 — the Cap
3 — the Cap
4 — Facing
5 — the Directing frame

6 — Back section of console assembly
7 — the lever Handle switching I transfers (RKPP)
8 — the Clamp
9 — Forward section of console assembly
10 — the Basic arm


Details of installation of sections of the central console on the Mirage models since 1997 of the issue.

1 — Back section of console assembly
2 — the Ashtray
3 — the Panel of facing of the radio tape recorder
4 — Forward section of console assembly

5 — the Facing panel of the lever of the selector (AT)
6 — Forward section of console assembly
7 — the Basic arm


Details of installation of sections of the central console on the Galant models for 1993 the issue.

1 — the Facing panel of the lever of gear shifting (RKPP)
2 — the Protective cover of the lever of gear shifting
3 — the Coaster
4 — the Console ware box
5 — the Cover of a console ware box
6 — Loopy clamps

7 — the Switch of management of functioning of the electric drive of door mirrors
8 — the Switch of the modes of the movement (POWER/ECONO)/cap
9 — the Switch of electronic control by system of hydrostrengthening a wheel/cap
10 — the Finishing panel
11 — Basic arms


Details of installation of sections of the central console on the Galant 1994 ÷ models of 1998 of the issue.

1 — the Handle of the lever of gear shifting (RKPP)
2 — the Panel of facing of the lever of gear shifting
3 — the Pocket
4 — the Central (console) section of finishing of the dashboard

5 — Forward section of console assembly
6 — the Basic arm And
7 — the Basic arm In


Details of installation of sections of the central console on the Galant models since 1999 of the issue.

1 — Facing of the lever of gear shifting
2 — the Coaster (models without armrests)
3 — the Armrest (models with armrests)
4 — the Basic arm And (models to be with armrests)
5 — Console assembly

6 — the Lower central panel of finishing
7 — the Ashtray
8 — the Basic arm With
9 — the Basic arm And


Details of installation of sections of the central console on the Diamante 1992 ÷ models of 1996 of the issue.

1 — the Ashtray/panel of switches
2 — the Switch/cap

3 — Console assembly


Details of installation of sections of the central console on the Diamante models since 1997 of the issue.

1 — the Coaster
2 — the Coin box
3 — the Finishing panel
4 — Side covers

5 — Console assembly
6 — the Basic arm And
7 — the Basic arm With


Back section

Removal

 PERFORMANCE ORDER

1. Details of installation of back section of the central console are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

On the models equipped with a pillow (Omiya) of safety wrap up a wire tip an insulating tape and get to work not less than 60 seconds during which there have to be SRS shutdowns later!

3. Open a cover of a console ware box.
4. In case of need unbend edge of a carpet in the lower part of console assembly.
5. Turn out the fixing screws located along lower, which back section of console assembly.
6. In case of need Remove caps and turn out forward fixing screws.
7. Lift the console and take it from the car.

On some models seat belts are passed through console assembly and they need to be released accurately from it.


Installation

 PERFORMANCE ORDER

Installation is made upside-down.


Forward section

Removal

 PERFORMANCE ORDER

1. Details of installation of forward section of the central console are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

On the models equipped with a pillow (Omiya) of safety wrap up a wire tip an insulating tape and get to work not less than 60 seconds during which there have to be SRS shutdowns later!

3. In case of need remove back section of the console.
4. In case of need remove an ashtray and a coaster.
5. In case of need remove carpet inserts of console assembly.
6. On models with RKPP remove the handle from the gear shifting lever.
7. On models remove the facing panel of the lever of the selector from AT.
8. Remove caps, turn out fixing screws and remove side covers of the console.
9. Remove caps of forward fixing screws.
10. Previously having marked, disconnect all electrical wiring brought to console assembly.
11. Turn out fixing screws and remove console assembly.


Installation

 PERFORMANCE ORDER

Installation is made upside-down.