5.9. Replacement of an electric motor of the drive of the fan of a heater

Details of installation of the fan of a heater on the Mirage 1990 ÷ models of 1992 of the issue.

1 — the Ware box
2 — a loudspeaker Lattice
3 — the Forward overlay of a door threshold (model with right-hand steering)
4 — the Knee emphasis (models with right-hand steering)
5 — the Assembly frame of a ware box
6 — Knee (models without back heater) / line (models with a back heater) an air duct
7 — the Socket of an electrical wiring of the driving motor of the fan
8 — the Hose

9 — the Control unit of system of the distributed injection (MPI)
10 — Ventilatory assembly
11 — a fan Casing
12 — Sealing laying
13 — the Nut of fastening of a krylchatka
14 — Krylchatka
15 — the Driving electric motor


Details of installation of the fan of a heater on the Mirage 1993 ÷ models of 1996 of the issue.

1 — Section of the lower finishing
2 — the Ware box
3 — the Panel of angular finishing

4 — the Assembly frame of a ware box
5 — Resistive assembly
6 — Assembly of the fan of a heater with the driving motor


Details of installation of the fan of a heater on the Mirage 1997 ÷ models of 2000 of the issue.

1 — Resistive assembly
2 — Assembly of the fan of a heater with a driving electric motor
3 — the Dashboard

4 — the Connecting sleeve (models without To/in)
5 — the Evaporator (models with To/in)
6 — a fan Casing


Details of installation of the fan of a heater on the Galant 1990 ÷ models of 1993 of the issue.

1 — the Persistent clamp
2 — the Ware box
3 — the Panel of the lower finishing
4 — an air supply Sleeve in foot wells
5 — Sockets of an electrical wiring of the relay of management of MFI and the sensor switch of illumination of a ware box
6 — the Assembly frame of a ware box
7 — the Forward overlay of a door threshold
8 — the engine management Module
9 — evaporator Fixture (models with To/in) / clamps of fastening of an air duct (model without To/in)

10 — the Hose
11 — Assembly of the fan with a casing
12 — the Driving electric motor
13 — Sealing laying
14 — the Nut of fastening of a krylchatka
15 — Krylchatka
16 — Assembly of the fan with the driving motor
17 — a fan Casing


Details of installation of the fan of a heater on the Galant 1994 ÷ models of 1998 of the issue.

1 — the Panel of the lower finishing
2 — Resistive assembly
3 — the ECM K/V compressor (model with To/in)
4 — Assembly of the fan of a heater
5 — the Dashboard

6 — the Clamp
7 — the Connecting sleeve (models without To/in)
8 — evaporator Fixture (models with To/in)
9 — a fan Casing



Details of installation of the fan of a heater on the Diamante 1992 ÷ models of 1996 of the issue.

1 — the Panel of the lower finishing
2 — an air supply Sleeve in foot wells
3 — the Assembly frame of a ware box
4 — evaporator Fixture
5 — Assembly of the motor of switching of the mode of circulation
6 — the Relay of management of MFI

7 — the MFI Control unit
8 — the Right lower arm of the dashboard
9 — Assembly of the fan of a heater with a casing
10 — Assembly of the fan of a heater
11 — a fan Casing


Details of installation of the fan of a heater on the Diamante 1997 ÷ models of 2000 of the issue.

1 — the Controller of blocking of the K/V driving belt
2 — Assembly of the fan of a heater

3 — the Relay of the high-speed mode of functioning of the fan of a heater


The cars considered in the present manual are equipped with system of additional safety of SRS better known as a safety cushion. Before performing any works near assembly of a pillow or a steering column, without fail disconnect system in order to avoid getting injured as a result of its casual operation, - disconnect from the battery at first a negative, then positive wire and wait not less than two minutes before starting service of the components located near sensors of the directed overloads (see the Head for Onboard electric equipment). Isolation and contact sockets of an electrical wiring of a chain of SRS are painted in bright yellow color. It is not necessary to connect any diagnostic units to this chain!


Mirage models

Removal

 PERFORMANCE ORDER

1. Details of installation of the fan of a heater on the Mirage models are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Remove the right section of the lower finishing of the dashboard (see the Head Kuzov).
4. Remove assembly of a ware box and its assembly frame (see the Head Kuzov).
5. Disconnect an electrical wiring from the driving motor of the fan of a heater.
6. Disconnect and remove resistive assembly.
7. Disconnect a ventilating tube of a driving electric motor.
8. Turn out fixing bolts and remove to the block of the driving motor. In case of need replace a krylchatka of the fan.


Installation

 PERFORMANCE ORDER

1. Establish assembly of a driving electric motor on the regular place and screw fixing bolts.
2. Connect an electrical wiring to the motor.
3. Connect a ventilating tube.


Galant 1993 ÷ models of 1993 of the issue.

Removal

 PERFORMANCE ORDER

1. Details of installation of the fan of a heater on the Galant 1990 ÷ models of 1993 of the issue are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Remove a clamp of a ware box.
4. Against the stop open a cover of a ware box and turn out the lower screws of fastening of assembly. Remove a ware box.
5. Remove the right section of the lower finishing of the dashboard (see the Head Kuzov).

Pay attention that some of fixing screws are closed by decorative covers which need previously to be removed.

6. Remove an air supply sleeve in a foot well of the forward passenger.
7. Disunite the 10-contact socket on the back party of an assembly frame of a ware box. Disconnect an electrical wiring from the box illumination sensor switch (it is also established on an assembly frame).
8. Turn out four fixing bolts and remove an assembly frame of a ware box.
9. Disconnect the small air hose going from a fan electric motor to a fan casing.
10. Disconnect an electrical wiring from the driving motor.
11. Turn out three fixing bolts and remove assembly of the fan from a casing. In case of need give a nut and remove a krylchatka.


Installation

 PERFORMANCE ORDER

1. Attentively examine a casing from within, having removed from it the garbage and foreign objects capable to place to rotation of a krylchatka.
2. Estimate a condition of sealing laying, in case of need make replacement.
3. Install the heater fan on the regular place. Screw and tighten fixing bolts.
4. Connect a ventilating hose and an electrical wiring to the driving motor.
5. Establish an assembly frame of a ware box and connect to it both electric sockets (10-contact and 1-contact).
6. Establish an air duct.
7. Establish section of the lower finishing of the dashboard, - track correctness of installation and reliability of a zashchelkivaniye of all clamps.
8. Establish a ware box with a persistent clamp.
9. Connect a negative wire to the battery.


Galant 1994 ÷ models of 2000 of the issue.

Removal

 PERFORMANCE ORDER

1. Details of installation of the fan of a heater on the Galant 1994 ÷ models of 2000 of the issue are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Turn out three fixing screws and remove the lower section of finishing of the dashboard (see the Head Kuzov).
4. On the models equipped with the air conditioning system remove the compressor module.
5. Disconnect an electrical wiring from a heater fan drive electric motor.
6. Turn out three fixing screws and remove ventilatory assembly from a casing.


Installation

 PERFORMANCE ORDER

1. Attentively examine a casing from within, having removed from it the garbage and foreign objects capable to place to rotation of a krylchatka.
2. Install the heater fan on the regular place. Screw and tighten fixing bolts.
3. Connect an electrical wiring to the driving motor.
4. At the corresponding complete set of the car install the К/В compressor module.
5. Establish section of the lower finishing of the dashboard, - track correctness of installation and reliability of a zashchelkivaniye of all clamps.
6. Connect a negative wire to the battery.


Diamante models

Removal

 PERFORMANCE ORDER

1. Details of installation of the fan of a heater on the Diamante models are shown on illustrations.
2. Disconnect safety cushions (see the Head Onboard electric equipment).
3. Remove the right section of the lower finishing of the dashboard and a sleeve of an air duct.
4. Remove the drummer of the lock of a ware box, assembly of a ware box and its external casing. Turn out the screw located under assembly.
5. Give evaporator casing fixture.
6. Remove assembly of the motor of switching of the mode of circulation.
7. Remove RSM, a basic arm and the relay of management of MFI.
8. Remove the right lower arm of the dashboard.
9. Disconnect a cast hose from ventilatory assembly.
10. Remove assembly of the fan.
11. In case of need give a fixing nut and remove a krylchatka.


Installation

 PERFORMANCE ORDER

1. Check a shaft of the driving pump for existence of signs of a bend. Estimate a condition of sealing laying. Carefully clear all details of assembly, blow an air duct.
2. Fix a krylchatka of the fan on a shaft of the driving pump.
3. Establish assembly on the regular place.
4. Connect a cast hose and an electrical wiring to the motor.
5. Screw a bolt of fastening of a casing of the evaporator.
6. Establish the right lower arm of the dashboard.
7. Establish RSM, a basic arm and the relay of management of MFI.
8. Establish assembly of the damping motor of switching of the mode of circulation.
9. Screw the screw located under assembly of a ware box, then establish a ware box, - act as it should be, the return to an order of dismantle of components.
10. Establish the lower section of finishing of the panel air duct devices/sleeve.
11. Connect a negative wire to the battery. Check serviceability of functioning of the automatic air conditioning system (climate control).