1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Disconnect a driving cable of the AT selector from the lever.

3. Turn out two fixing screws and remove the sensor switch.

1. Install the sensor switch on the regular place. Screw fixing bolts, however do not tighten them before completion of adjustment of the sensor switch.
2. Connect an electrical wiring to the sensor switch and make its adjustment (see below).
3. Connect a negative wire to the battery.
4. Make sure that start of the engine is obviously possible only in provisions "P" and "N" of transmission. Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to situation "R".

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Cock the parking brake and prop up car wheels antiretractable boots.
3. Find the sensor switch of permission of start installed from above on a transmission case.
4. Weaken an adjusting nut of a cable of the drive of switching on a transmission case. In interior of the car transfer the selector lever to situation "N".
5. Also transfer the hand lever of management of switching of transmission to situation "N".
6. Release screws of fastening of the sensor switch and develop the last so that the 5-millimeter opening in its case was combined with a reciprocal opening (also 5-millimitrovy) in the hand lever of switching.
7. Tighten bolts of fastening of the sensor switch with the required effort (10 ÷ 12H • м).
8. Having delayed a driving cable around an adjusting nut, completely choose its weak point, then tighten a nut with effort 12 H • m.
9. Make sure that the sensor switch lever when switching the AT modes from salon moves to the relevant provision.
10. Connect a negative wire to the battery.
11. Make sure that start of the engine is possible only in provisions "P" and "N" of transmission. Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to situation "R".

1. The sensor switch of permission of start on these models also is from above on a transmission case.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Disconnect a driving cable of the AT selector from the lever.
4. Give a nut of fastening of a driving cable of management of switching of transmission to the hand lever of transmission. Take a cable aside.
5. Transfer the hand lever to situation "N", then give a nut on the lever.
6. Disconnect an electrical wiring from the sensor switch of permission of start.
7. Turn out fixing bolts and remove the sensor switch.

1. Install the sensor switch on the regular place. Screw, but do not tighten still fixing bolts.
2. Connect the hand lever to the sensor switch and fix it by a nut, - track that the lever remained in situation "N".
3. Execute adjustment of the sensor switch (see below), then finally tighten bolts of fastening of the sensor switch with the required effort (11 H • м).
4. Connect an electrical wiring to the sensor switch.
5. Connect a switching drive cable, choose its weak point, check freedom of movement of the lever and tighten a nut of fastening of a cable.
6. Connect a negative wire to the battery.
7. Make sure that start of the engine is obviously possible only in provisions "P" and "N" of transmission. Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to situation "R".

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Cock the parking brake and prop up car wheels antiretractable boots.
3. Find the sensor switch of permission of start installed from above on a transmission case.
4. Weaken an adjusting nut of a cable of the drive of switching on a transmission case. In interior of the car transfer the selector lever to situation "N".
5. Also transfer the hand lever of management of switching of transmission to situation "N".
6. Release screws of fastening of the sensor switch and develop the last so that the 5-millimeter opening in its case was combined with a reciprocal opening (also 5-millimitrovy) in the hand lever of switching, - pass a drill of suitable diameter throughout openings and tighten bolts of fastening of the sensor switch with the required effort (11 H • м).
7. Having delayed a driving cable around an adjusting nut, completely choose its weak point, then tighten a nut with effort 12 H • m.
8. Check freedom of the course of the hand lever.
9. Connect a negative wire to the battery.
10. Make sure that start of the engine is possible only in provisions "P" and "N" of transmission. Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to situation "R".

2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

3. Turn out two fixing bolts and remove the sensor switch.

1. Install the sensor switch on the regular place. Screw, but do not tighten still fixing bolts.
2. Execute adjustment of the sensor switch (see below), then finally tighten bolts of fastening of the sensor switch with the required effort (10 ÷ 12 H • м).
3. Connect a switching drive cable.
4. Connect a negative wire to the battery.
5. Connect an electrical wiring to the sensor switch.
6. Make sure that start of the engine is possible only in provisions "P" and "N" of transmission. Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to situation "R".

1. Adjustment, as well as earlier, is made by combination of 5-millimeter openings in the case of the sensor switch and a body of the hand lever of the drive of switching.
2. In conclusion make sure that start of the engine is possible only in provisions "P" and "N" of transmission. Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to situation "R".